http://wiki.eth0.nl/api.php?action=feedcontributions&feedformat=atom&user=KingOfDos 2026-04-19T11:53:26Z User contributions MediaWiki 1.34.1 http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10407 2012-01-31T14:22:51Z

<p>KingOfDos: /* Power Fail Circuit */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view HACKS ===<br /> <br /> KingOfDos schematic:<br /> http://kingofdos.com/zooi/beck_sc12/beckboard-custom-kod-v6.png<br /> Older variants are NOT functional. Will document stuff later...<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> === ChipTool on WINE ===<br /> <br /> Make serial port available within Wine:<br /> ln -s /dev/ttyUSB0 ~/.wine/dosdevices/com2<br /> <br /> Tested:<br /> * Format_sc1x.hex<br /> * Beck SC12 v1.25 BIOS 'large' .hex<br /> * Sometimes the tool will detect the beck via ethernet (in Wine). Sometimes it won't... Unsure if that's a broadcast limit @ switch, or some WINE issue (didn't research it, so far).<br /> * Flashing works via Ethernet (worked once @ KingOfDos). If the Beck is detected.... And because of this issues '''I will recommand the use of a serial cable'''. What will happen if WINE/something stops working at the flashing point?<br /> <br /> You'd need to connect the RXD, TXD and GND from a RS232/DB9, to pins of the RJ12 @ Beck. RTS/CTS not required when flashing.<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> ==== Power Fail Circuit ====<br /> If this is in the chip.ini (and only then!):<br /> [DEVICE]<br /> PFI_ENABLE=1<br /> This will enable the PFI function. Which results in: &quot;If you don't have a power fail circuit connected to the PFI pin, else the chip will not boot and the RTOS will not come up anymore, because the PIO9 pin, if unconnected, is normally high (input with pullup).&quot;<br /> Source: http://www.beck-ipc.com/files/api/scxxx/config.htm#DEVICE_PFI_ENABLE<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> export PATH=$PATH:$WATCOM/binl<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == ST232C chip verkeerd om op het bord ==<br /> <br /> Let op, er zijn 2 soorten van dit bord.<br /> 1 er van heeft de st232c chip verkeerd om zitten:<br /> <br /> [[image:Beckboardfout.jpg|400px]] [[image:Beckboardgoed.jpg|400px]]<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10406 2012-01-31T14:18:13Z

<p>KingOfDos: /* Debugging */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view HACKS ===<br /> <br /> KingOfDos schematic:<br /> http://kingofdos.com/zooi/beck_sc12/beckboard-custom-kod-v6.png<br /> Older variants are NOT functional. Will document stuff later...<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> === ChipTool on WINE ===<br /> <br /> Make serial port available within Wine:<br /> ln -s /dev/ttyUSB0 ~/.wine/dosdevices/com2<br /> <br /> Tested:<br /> * Format_sc1x.hex<br /> * Beck SC12 v1.25 BIOS 'large' .hex<br /> * Sometimes the tool will detect the beck via ethernet (in Wine). Sometimes it won't... Unsure if that's a broadcast limit @ switch, or some WINE issue (didn't research it, so far).<br /> * Flashing works via Ethernet (worked once @ KingOfDos). If the Beck is detected.... And because of this issues '''I will recommand the use of a serial cable'''. What will happen if WINE/something stops working at the flashing point?<br /> <br /> You'd need to connect the RXD, TXD and GND from a RS232/DB9, to pins of the RJ12 @ Beck. RTS/CTS not required when flashing.<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> ==== Power Fail Circuit ====<br /> If this is in the chip.ini (and only then!):<br /> [DEVICE]<br /> PFI_ENABLE=0/1<br /> &quot;If you don't have a power fail circuit connected to the PFI pin, else the chip will not boot and the RTOS will not come up anymore, because the PIO9 pin, if unconnected, is normally high (input with pullup).&quot;<br /> Source: http://www.beck-ipc.com/files/api/scxxx/config.htm#DEVICE_PFI_ENABLE<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> export PATH=$PATH:$WATCOM/binl<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == ST232C chip verkeerd om op het bord ==<br /> <br /> Let op, er zijn 2 soorten van dit bord.<br /> 1 er van heeft de st232c chip verkeerd om zitten:<br /> <br /> [[image:Beckboardfout.jpg|400px]] [[image:Beckboardgoed.jpg|400px]]<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10398 2012-01-30T16:26:50Z

<p>KingOfDos: /* De laatste BIOS versie 1.25 Flashen */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view HACKS ===<br /> <br /> KingOfDos schematic:<br /> http://kingofdos.com/zooi/beck_sc12/beckboard-custom-kod-v6.png<br /> Older variants are NOT functional. Will document stuff later...<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> === ChipTool on WINE ===<br /> <br /> Make serial port available within Wine:<br /> ln -s /dev/ttyUSB0 ~/.wine/dosdevices/com2<br /> <br /> Tested:<br /> * Format_sc1x.hex<br /> * Beck SC12 v1.25 BIOS 'large' .hex<br /> * Sometimes the tool will detect the beck via ethernet (in Wine). Sometimes it won't... Unsure if that's a broadcast limit @ switch, or some WINE issue (didn't research it, so far).<br /> * Flashing works via Ethernet (worked once @ KingOfDos). If the Beck is detected.... And because of this issues '''I will recommand the use of a serial cable'''. What will happen if WINE/something stops working at the flashing point?<br /> <br /> You'd need to connect the RXD, TXD and GND from a RS232/DB9, to pins of the RJ12 @ Beck. RTS/CTS not required when flashing.<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> export PATH=$PATH:$WATCOM/binl<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == ST232C chip verkeerd om op het bord ==<br /> <br /> Let op, er zijn 2 soorten van dit bord.<br /> 1 er van heeft de st232c chip verkeerd om zitten:<br /> <br /> [[image:Beckboardfout.jpg|400px]] [[image:Beckboardgoed.jpg|400px]]<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10397 2012-01-30T01:43:34Z

<p>KingOfDos: /* Top view HACKS */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view HACKS ===<br /> <br /> KingOfDos schematic:<br /> http://kingofdos.com/zooi/beck_sc12/beckboard-custom-kod-v6.png<br /> Older variants are NOT functional. Will document stuff later...<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> export PATH=$PATH:$WATCOM/binl<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == ST232C chip verkeerd om op het bord ==<br /> <br /> Let op, er zijn 2 soorten van dit bord.<br /> 1 er van heeft de st232c chip verkeerd om zitten:<br /> <br /> [[image:Beckboardfout.jpg|400px]] [[image:Beckboardgoed.jpg|400px]]<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10396 2012-01-30T01:41:24Z

<p>KingOfDos: /* Top view CUSTOM HACKS */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view HACKS ===<br /> <br /> KingOfDos schematic:<br /> http://kingofdos.com/zooi/beck_sc12/beckboard-custom-kod-v5.png<br /> Older variants are NOT functional. Will document stuff later...<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> export PATH=$PATH:$WATCOM/binl<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == ST232C chip verkeerd om op het bord ==<br /> <br /> Let op, er zijn 2 soorten van dit bord.<br /> 1 er van heeft de st232c chip verkeerd om zitten:<br /> <br /> [[image:Beckboardfout.jpg|400px]] [[image:Beckboardgoed.jpg|400px]]<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10381 2012-01-28T15:37:55Z

<p>KingOfDos: /* Top view CUSTOM HACKS */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC &lt;------------------- I/O Beck AD0 pin 8 --&gt; Note: This pins are not connected on default. Please use <br /> # (J4) NC &lt;------------------- I/O Beck AD1 pin 9 ::: 80-wire IDE cable (thick enough for that less mA max!).<br /> # (J4) NC &lt;------------------- I/O Beck AD2 pin 10<br /> # (J4) NC &lt;------------------- I/O Beck AD3 pin 11<br /> # (J4) NC &lt;------------------- I/O Beck AD4 pin 12<br /> # (J4) NC &lt;------------------- I/O Beck AD5 pin 13<br /> # (J4) NC &lt;------------------- I/O Beck AD6 pin 14<br /> # (J4) NC &lt;------------------- I/O Beck AD7 pin 15<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> <br /> Above hacks, as image (for now, as link. so we won't fill the entire page):<br /> http://kingofdos.com/zooi/beck_sc12/beckboard-custom-kod-v5.png<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10380 2012-01-28T13:38:35Z

<p>KingOfDos: /* Top view CUSTOM HACKS */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC &lt;------------------- I/O Beck AD0 pin 8 --&gt; Note: This pins are not connected on default. Please use <br /> # (J4) NC &lt;------------------- I/O Beck AD1 pin 9 ::: 80-wire IDE cable (thick enough for that less mA max!).<br /> # (J4) NC &lt;------------------- I/O Beck AD2 pin 10<br /> # (J4) NC &lt;------------------- I/O Beck AD3 pin 11<br /> # (J4) NC &lt;------------------- I/O Beck AD4 pin 12<br /> # (J4) NC &lt;------------------- I/O Beck AD5 pin 13<br /> # (J4) NC &lt;------------------- I/O Beck AD6 pin 14<br /> # (J4) NC &lt;------------------- I/O Beck AD7 pin 15<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> <br /> Above hacks, as image (for now, as link. so we won't fill the entire page):<br /> http://kingofdos.com/zooi/beck_sc12/beckboard-custom-kod-v3.png<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10377 2012-01-28T00:24:54Z

<p>KingOfDos: /* Top view CUSTOM HACKS */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC &lt;------------------- I/O Beck AD0 pin 8 --&gt; Note: This pins are not connected on default. Please use <br /> # (J4) NC &lt;------------------- I/O Beck AD1 pin 9 ::: 80-wire IDE cable (thick enough for that less mA max!).<br /> # (J4) NC &lt;------------------- I/O Beck AD2 pin 10<br /> # (J4) NC &lt;------------------- I/O Beck AD3 pin 11<br /> # (J4) NC &lt;------------------- I/O Beck AD4 pin 12<br /> # (J4) NC &lt;------------------- I/O Beck AD5 pin 13<br /> # (J4) NC &lt;------------------- I/O Beck AD6 pin 14<br /> # (J4) NC &lt;------------------- I/O Beck AD7 pin 15<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> # (J4) FLYING<br /> <br /> Above hacks, as image (for now, as link. so we won't fill the entire page):<br /> http://kingofdos.com/zooi/beck_sc12/beckboard-custom-kod-v1.png<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10376 2012-01-27T18:53:13Z

<p>KingOfDos: /* OpenWatCom */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC &lt;------------------- I/O Beck AD0 --&gt; Note: This pins are not connected on default. Please use <br /> # (J4) NC &lt;------------------- I/O Beck AD1 ::: 80-wire IDE cable (thick enough for that less mA max!).<br /> # (J4) NC &lt;------------------- I/O Beck AD2<br /> # (J4) NC &lt;------------------- I/O Beck AD3<br /> # (J4) NC &lt;------------------- I/O Beck AD4<br /> # (J4) NC &lt;------------------- I/O Beck AD5<br /> # (J4) NC &lt;------------------- I/O Beck AD6<br /> # (J4) NC &lt;------------------- I/O Beck AD7<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == De laatste BIOS versie 1.25 Flashen ==<br /> Dit moet op een Windows station gebeuren (eventueel eentje in een VM).<br /> * Download [http://www.beck-ipc.com/files/tools/Chiptool_Install_V6.1.3.6.exe Beck Chiptool]<br /> * Download [http://www.beck-ipc.com/files/rtos/SC12V0125.zip SC12 Bios V1.25]<br /> * Pak het Bios bestand ergens uit<br /> * start Chiptool<br /> * Flash-&gt;Program flash<br /> * Kies een van de versies in de directory van het uitgepakge BIOS bestand, bv. SC12V0125_LARGE.hex<br /> * Vul het IP-adres van het beck-board in en klik 'Start' bij 'Use UDP/IP' en wacht geduldig tot het programmeren is voltooid.<br /> <br /> Het user/password voor telnet is nu tel/tel en bij ftp ftp/ftp.&lt;br/&gt;<br /> Het periodieke reset probleem is dan ook vanzelf opgelost.&lt;br/&gt;<br /> Het tcp2con programma is dan wel verdwenen... maar wat doet dat programma sowieso in hemelsnaam<br /> <br /> == Ramdisk aanmaken voor ontwikkeling ==<br /> Hiermee beperk je het aantal flashes op de beck-chip.<br /> <br /> Creeer op A: een bestand CHIP.INI met inhoud<br /> [RAMDRIVE]<br /> SIZE=64<br /> <br /> Hiermee krijg je een ramdisk van 64k. De driveletter is C:<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Een aangepaste [http://tkkrlab.nl/w/images/d/dd/Clib.tar.gz clib.tar.gz] is beschikbaar (voornamelijk alle .h filenamen en verwijzingen ernaar lowercase gemaakt).&lt;br/&gt;<br /> Op basis van de oorspronkelijke [http://www.beck-ipc.com/files/libs/clibV222src.zip beck rtos c library].&lt;br/&gt;<br /> Hieronder een voorbeeld hoe een C programma te compileren voor het beck-board:<br /> <br /> # WATCOM laten wijzen waar openwatcom is geinstalleerd<br /> export WATCOM=~/watcom/<br /> # watcom omgeving instellen<br /> . $WATCOM/owsetenv.sh<br /> # BECKCLIB laten wijzen naar aangepaste library (headers en libraries)<br /> export BECKCLIB=~/beck/clib<br /> <br /> # voorbeeld compileren en linken C file<br /> wcc -I$BECKCLIB tcpserv.c<br /> wlink format dos libpath $WATCOM/lib286/dos:$WATCOM/lib286:$BECKCLIB name tcpserv.exe file tcpserv.o library clib222s.lib<br /> <br /> hierna kun je de .exe file ftp'en naar het beck board, niet vergeten binary mode aan te zetten! Bij het ontwikkelen kun je het beste een ramdisk gebruiken om de flash te sparen<br /> <br /> In het bovenstaande verhaal ontbreken de juiste compiler options:<br /> wcc -w4 -s -zp1 -d0 -fpi -zu -1 -ml<br /> Warning level 4, Disable Depth Checking, 1 byte allignment, No debugging, Floating Point: inline with emulator, SS!=DS, 80186, Large Memory Model<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://www.beck-ipc.com/en/products/sc1x/sc13.asp Bios upgrade<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10366 2012-01-23T23:07:27Z

<p>KingOfDos: /* Top view CUSTOM HACKS */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC &lt;------------------- I/O Beck AD0 --&gt; Note: This pins are not connected on default. Please use <br /> # (J4) NC &lt;------------------- I/O Beck AD1 ::: 80-wire IDE cable (thick enough for that less mA max!).<br /> # (J4) NC &lt;------------------- I/O Beck AD2<br /> # (J4) NC &lt;------------------- I/O Beck AD3<br /> # (J4) NC &lt;------------------- I/O Beck AD4<br /> # (J4) NC &lt;------------------- I/O Beck AD5<br /> # (J4) NC &lt;------------------- I/O Beck AD6<br /> # (J4) NC &lt;------------------- I/O Beck AD7<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> # (J4) FLYING &lt;-------------- Make J4 a 2x8 header. To support more pins at the SC12. Schematic later!!!<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> Settings which may work for Beck SC12, seen on: http://www.prouc.de/main.php?in=10<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Working on a build env for Beck SC12.....<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10361 2012-01-19T14:19:33Z

<p>KingOfDos: /* OpenWatCom */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> Settings which may work for Beck SC12, seen on: http://www.prouc.de/main.php?in=10<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Working on a build env for Beck SC12.....<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10360 2012-01-19T14:17:55Z

<p>KingOfDos: /* Compilers */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> 8086 or 80186. not i286 or i386!<br /> Large Memory Mode (SC12 has dual extended memory, or something)<br /> <br /> === OpenWatCom ===<br /> Settings which may work for Beck SC12, seen on: www.prouc.de/main.php?in=10<br /> <br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Working on a build env for Beck SC12.....<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10359 2012-01-19T14:15:57Z

<p>KingOfDos: /* Software */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Compilers ==<br /> === OpenWatCom ===<br /> Error: while installing the linux binary package<br /> [1] 20858 floating point exception ./open-watcom-c-linux-1.9<br /> Solution (by The_Niz, via http://www.openwatcom.org/index.php/Installing_Open_Watcom_on_Linux )<br /> export TERMINFO=/lib/terminfo<br /> ./open-watcom-c-linux-1.9<br /> <br /> Working on a build env for Beck SC12.....<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10358 2012-01-18T15:36:56Z

<p>KingOfDos: /* How to avoid periodic resets */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> '''Note: Please remove this, before flashing new firmware to device!''' Maybe this reboot will kill a flash over ethernet? As long the bootloader works, you can flash it over serial again. But still, it's quite risky.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> ** https://wiki.bitlair.nl/Pages/Bestand:010036-11.zip de files van elektuur<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10356 2012-01-18T01:57:46Z

<p>KingOfDos: /* Top view CUSTOM HACKS */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10355 2012-01-18T01:57:14Z

<p>KingOfDos: /* Top view */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 -&gt; max488 pin 5 (Y) --&gt; Wire colors removed! They differ at boards. pin/wire layout won't (as far I can tell).<br /> # (J2) rs422 -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 -&gt; max488 pin 7 (B)<br /> # (J2) rs422 -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10354 2012-01-18T01:47:56Z

<p>KingOfDos: /* Links */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://www.beck-ipc.com/en/download/index.asp &lt;- choose SC12 in &lt;select&gt;box (at the 2nd block, @ bottom).<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> * http://www.zengers.net/index.php?option=content&amp;task=view&amp;id=12&amp;Itemid=2 &lt;- 3 pages uit Elektuur, Nederlandse manual (misschien uploaden op eth0 wiki?)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10353 2012-01-18T01:05:26Z

<p>KingOfDos: /* Hardware */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10352 2012-01-18T01:05:04Z

<p>KingOfDos: /* Software */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10351 2012-01-18T01:04:32Z

<p>KingOfDos: /* How to avoid periodic resets */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == How to avoid periodic resets ==<br /> * Disable tcp2con.exe in autoexec.bat<br /> It looks like tcp2con.exe performs a device reset after 120 sec.<br /> <br /> == CGI HTTP ==<br /> Default tools available:<br /> * http://1.2.3.4/ChipCfg<br /> * http://1.2.3.4/TCP2COM (reverse engineer, or write our own software)<br /> <br /> == Debugging ==<br /> === Hardware ===<br /> &quot;If it fails, the @CHIP prints the error message &quot;RAM ERROR&quot; on '''the COM port (using 19200 Baud and 8N1, regardless the entry in the CHIP.INI).&quot;'''<br /> Source: http://isa.umh.es/temas/micros/doc/sc12/doc/bootfc.htm<br /> <br /> === Software ===<br /> Use TRACE.EXE (seen in manual, link page here!) or maybe use the remote SYSLOG daemon ( http://www.lourensrozema.nl/ax/download/syslog_src.zip is ASM! untested..)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10347 2012-01-17T16:30:06Z

<p>KingOfDos: /* Top view CUSTOM HACKS */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Top view CUSTOM HACKS ===<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10346 2012-01-17T16:29:37Z

<p>KingOfDos: /* Top view */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> == Top view CUSTOM HACKS ==<br /> <br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected) &lt;---- use for POE PLUS, connect to RJ45 at board? schematic/idea for 802.2af OR 7805 switch later. ask KingOfDos<br /> # (J5) NC &lt;-------------------- use for POE GND, connect to RJ45 at board.<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 31, I2CCLK?<br /> # (J5) NC &lt;-------------------- Solder this to the SC12 pin 30, I2CDAT?<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J7) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6) Output optocoupler U1<br /> # (J6) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP<br /> <br /> == IRC ==<br /> * network: oftc (irc.oftc.net)<br /> * chan: #SC12</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10341 2012-01-16T16:20:34Z

<p>KingOfDos: /* Links */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6/J7) Output optocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources incl '''remote syslog''')<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10340 2012-01-16T16:06:36Z

<p>KingOfDos: /* Chip.ini */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> More? See http://isa.umh.es/temas/micros/doc/sc12/doc/config.htm<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6/J7) Output optocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10339 2012-01-16T16:06:05Z

<p>KingOfDos: /* OUI vs Serial# */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (24 bit) serial number, written as 5 characters (hex).<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> Interrupt 0xA0 service 0x00: Get serial number.<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#0xA00x00<br /> Interrupt 0xA0 service 0x17: Get MAC address of the Ethernet interface<br /> http://isa.umh.es/temas/micros/doc/sc12/doc/biosints.htm#Interrupt_0xA0_function_0x17__Get_MAC_address_of_the_Ethernet_interface<br /> <br /> Memory map says: 0400h - 04FFh for MAC Address. Possible to change MAC addr (plz check later)? I guess that 'on boot, the default mac == serial'. And that we could configure it via program at boot?<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6/J7) Output optocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10338 2012-01-16T14:06:52Z

<p>KingOfDos: /* Specs */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs422 (via max488)<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == OUI vs Serial# ==<br /> <br /> * OUI 00:30:56 'Beck IPC GmbH'<br /> * MacAddr format: 00:30:56:f'''x:xx:xx''', the xxx is (40 bit) serial number.<br /> <br /> Example:<br /> A:\&gt;ver<br /> ...cut...<br /> Target=SC12 Serialnumber=xxxxx<br /> ...cut...<br /> A:\&gt;<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6/J7) Output optocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> * ftp://212.71.131.133/pub/beck/software/<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10333 2012-01-16T01:57:48Z

<p>KingOfDos: /* Bottom view */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs488<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> OUI 00:30:56 'Beck IPC GmbH' (report if other!)<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6/J7) Output potocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led (connected to red led)<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10332 2012-01-16T01:54:58Z

<p>KingOfDos: /* Bottom view */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs488<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> OUI 00:30:56 'Beck IPC GmbH' (report if other!)<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6/J7) Output potocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> Note:<br /> * Pin17 @ SC12 = Link Led<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10331 2012-01-16T01:40:36Z

<p>KingOfDos: /* Pinout */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs488<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> OUI 00:30:56 'Beck IPC GmbH' (report if other!)<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout / Board desc ==<br /> <br /> === Top view ===<br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6/J7) Output potocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> === Bottom view ===<br /> <br /> * Pin 17 @ BECK SC12 'RESET / NMI / LINK LED.' -&gt; Connected to red led at board, near the text 'art.' at the right bottom.<br /> <br /> For pinout @ BECK, see Datasheet, page 5.<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10330 2012-01-16T01:34:05Z

<p>KingOfDos: /* Pinout */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs488<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> OUI 00:30:56 'Beck IPC GmbH' (report if other!)<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout ==<br /> <br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs422 green -&gt; max488 pin 5 (Y)<br /> # (J2) rs422 white/green -&gt; max488 pin 6 (Z)<br /> # (J2) rs422 orange -&gt; max488 pin 7 (B)<br /> # (J2) rs422 white/orange -&gt; max488 pin 8 (A)<br /> # (J6/J7) Output potocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10329 2012-01-16T01:32:39Z

<p>KingOfDos: /* Specs */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs488<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> OUI 00:30:56 'Beck IPC GmbH' (report if other!)<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout ==<br /> <br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs488 green ?<br /> # (J2) rs488 white/green ?<br /> # (J2) rs488 orange ?<br /> # (J2) rs488 white/orange ?<br /> # (J6/J7) Output potocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10328 2012-01-15T23:33:13Z

<p>KingOfDos: /* Links */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs488<br /> * [[file:SCHEMA.pdf‎]]<br /> * [[file:Startup.pdf‎]]<br /> * [[file:Controller_datasheet.pdf‎]]<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout ==<br /> <br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs488 green ?<br /> # (J2) rs488 white/green ?<br /> # (J2) rs488 orange ?<br /> # (J2) rs488 white/orange ?<br /> # (J6/J7) Output potocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player + ide disk, incl some .zip files (schematics, sources)<br /> * http://www.psh-mikro.sk/beck/Beck_mod_de.htm &lt;- CompactFlash something (schematic + demo program)<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Sc12_ipc@chip&diff=10320 2012-01-15T23:16:49Z

<p>KingOfDos: /* Links */</p> <hr /> <div>This is a page about the boards SA007 brought to eth0:winter 2k12.<br /> <br /> == Specs ==<br /> <br /> * Beck IPC@Chip SC12<br /> * AMD 80186 @ 20Mhz<br /> * 512kb ram<br /> * 512kb flash<br /> * 10mbit ethernet<br /> * rs232+rs488<br /> <br /> == Chip.ini ==<br /> <br /> [IP]<br /> NETMASK=255.255.255.0<br /> ADDRESS=10.10.1.61<br /> DHCP=1<br /> [TELNET]<br /> USER0=tel<br /> PASSWORD0=IPC-03<br /> [FTP]<br /> USER0=ftp<br /> PASSWORD0=IPC-03<br /> [STDIO]<br /> STDIN=TELNET<br /> STDOUT=TELNET<br /> <br /> == Pinout ==<br /> <br /> [[Image:IPCboard-top.png]]<br /> <br /> # (J5) +5v <br /> # (J5) GND<br /> # (J5) NC (not connected)<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) NC<br /> # (J5) Input optocoupler U1<br /> # (J5) Input optocoupler U2<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J4) NC<br /> # (J6) Output optocoupler U2<br /> # (J7) Output optocoupler U2<br /> # (J2) rs488 green ?<br /> # (J2) rs488 white/green ?<br /> # (J2) rs488 orange ?<br /> # (J2) rs488 white/orange ?<br /> # (J6/J7) Output potocoupler U1<br /> # (J6/J7) Output optocoupler U1<br /> <br /> == Links ==<br /> * http://isa.umh.es/temas/micros/doc/sc12/SC12V110_ReleaseNotes.pdf<br /> * http://www.beck-ipc.com/files/api/scxxx/program.htm<br /> * http://wunderkis.de/scbrd/index.html<br /> * http://isa.umh.es/temas/micros/soft/sc12/<br /> * http://isa.umh.es/temas/micros/doc/sc12/<br /> * http://xforce.iss.net/xforce/xfdb/8922 &lt;- IPC@CHIP Web server root directory is set to the system root, aka, access all the files!<br /> * http://www.openwatcom.org/index.php/Main_Page &lt;- compiler for 16bit dos apps, that runs on linux<br /> * http://www.weerschip.nl/download_beck.html &lt;- weather station, with software examples (1 zip checked with 'grep -i beck *')<br /> * http://www.lourensrozema.nl/ax/index.php?page=home.inc &lt;- mp3 player, incl some .zip files<br /> <br /> == Hackerspace working on/with them ==<br /> * http://www.tkkrlab.nl/wiki/Beck_board_ipc_2001<br /> * http://nurdspace.nl/IPC@Chip_boards<br /> * https://wiki.bitlair.nl/Pages/Projects/SA12_IPC@CHIP</div>

KingOfDos http://wiki.eth0.nl/index.php?title=User:KingOfDos&diff=7516 2010-08-06T09:53:54Z

<p>KingOfDos: </p> <hr /> <div>[[File:King-vlechtjes.jpg|200px|thumb|left|Photograph of KOD]] Roel Jansen (aka KingOfDos)<br /> <br /> Fulltime webdeveloper (HTML, CSS, JS, PHP, MySQL).<br /> <br /> Hobby: Electronics (uC/iC/etc), Telephone systems (including rotary / VoIP), some wireless stuff.<br /> <br /> To contact me, query on IRC (nick KingOfDos at rev-dns *.kingofdos.net), or figure out my other contact information somehow.</div>

KingOfDos http://wiki.eth0.nl/index.php?title=User:KingOfDos&diff=7509 2010-08-06T09:40:58Z

<p>KingOfDos: </p> <hr /> <div>[[File:King-vlechtjes.jpg|200px|thumb|left|Photograph of KOD]]]] Roel Jansen (aka KingOfDos)<br /> <br /> Fulltime webdeveloper (HTML, CSS, JS, PHP, MySQL).<br /> <br /> Hobby: Electronics (uC/iC/etc), Telephone systems (including rotary / VoIP), some wireless stuff.<br /> <br /> To contact me, query on IRC (nick KingOfDos at rev-dns *.kingofdos.net), or figure out my other contact information somehow.<br /> <br /> Some random project images:<br /> * http://kingofdos.com/zooi/rgblamp/117153.jpg<br /> * http://kingofdos.com/zooi/ledboard/front/2009-07-27%2017.37.02.jpg<br /> * more, soon when my website is updated.</div>

KingOfDos http://wiki.eth0.nl/index.php?title=User:KingOfDos&diff=7508 2010-08-06T09:40:45Z

<p>KingOfDos: </p> <hr /> <div>Roel Jansen (aka KingOfDos)<br /> <br /> Fulltime webdeveloper (HTML, CSS, JS, PHP, MySQL).<br /> <br /> Hobby: Electronics (uC/iC/etc), Telephone systems (including rotary / VoIP), some wireless stuff.<br /> <br /> To contact me, query on IRC (nick KingOfDos at rev-dns *.kingofdos.net), or figure out my other contact information somehow.<br /> <br /> Some random project images:<br /> * http://kingofdos.com/zooi/rgblamp/117153.jpg<br /> * http://kingofdos.com/zooi/ledboard/front/2009-07-27%2017.37.02.jpg<br /> * more, soon when my website is updated.<br /> <br /> [[File:King-vlechtjes.jpg|200px|thumb|left|Photograph of KOD]]]]</div>

KingOfDos http://wiki.eth0.nl/index.php?title=File:King-vlechtjes.jpg&diff=7506 2010-08-06T09:39:25Z

<p>KingOfDos: </p> <hr /> <div></div>

KingOfDos http://wiki.eth0.nl/index.php?title=User:KingOfDos&diff=7504 2010-08-06T09:37:40Z

<p>KingOfDos: </p> <hr /> <div>Roel Jansen (aka KingOfDos)<br /> <br /> Fulltime webdeveloper (HTML, CSS, JS, PHP, MySQL).<br /> <br /> Hobby: Electronics (uC/iC/etc), Telephone systems (including rotary / VoIP), some wireless stuff.<br /> <br /> To contact me, query on IRC (nick KingOfDos at rev-dns *.kingofdos.net), or figure out my other contact information somehow.<br /> <br /> Some random project images:<br /> * http://kingofdos.com/zooi/rgblamp/117153.jpg<br /> * http://kingofdos.com/zooi/ledboard/front/2009-07-27%2017.37.02.jpg<br /> * more, soon when my website is updated.<br /> <br /> [[Image:pic-KingOfDos.png]]</div>

KingOfDos http://wiki.eth0.nl/index.php?title=File:Pic-KingOfDos.png&diff=7503 2010-08-06T09:37:21Z

<p>KingOfDos: mehe ;)</p> <hr /> <div>mehe ;)</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7266 2010-07-27T12:34:00Z

<p>KingOfDos: /* Friday 6 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Aequitas|Aequitas]] ?<br /> # [[User:KingOfDos|KingOfDos]] misschien (dan kan ik volgende ochtend meteen aan de gang)<br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> # [[User:Diggie|diggie]] - Waarsch. zondag aankomst. Ben met camper, dus kan ook buiten 't terrein ergens gaan staan.<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> # [[User:Diggie|diggie]]<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> # [[User:Diggie|diggie]] - ik moet 's avonds wel ff 'n paar uurtjes weg<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> # [[User:Diggie|diggie]] (jarig! :-)<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> # [[User:Diggie|diggie]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> # [[User:Diggie|diggie]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> # [[User:Diggie|diggie]] - misschien<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> # [[User:Diggie|diggie]] - misschien</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7258 2010-07-27T12:10:21Z

<p>KingOfDos: /* Vrijdag 13 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> # [[User:Failbaitr|Jan]]<br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7257 2010-07-27T12:10:08Z

<p>KingOfDos: /* Donderdag 12 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> # [[User:Failbaitr|Jan]]<br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7256 2010-07-27T12:09:57Z

<p>KingOfDos: /* Woensdag 11 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> # [[User:Failbaitr|Jan]]<br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7255 2010-07-27T12:09:46Z

<p>KingOfDos: /* Dinsdag 10 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> # [[User:Failbaitr|Jan]]<br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7253 2010-07-27T12:08:55Z

<p>KingOfDos: /* Zondag 15 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> <br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7252 2010-07-27T12:08:46Z

<p>KingOfDos: /* Zaterdag 14 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> <br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7251 2010-07-27T12:08:17Z

<p>KingOfDos: /* Maandag 9 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> <br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7250 2010-07-27T12:08:01Z

<p>KingOfDos: /* Zondag 8 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> <br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko</div>

KingOfDos http://wiki.eth0.nl/index.php?title=BuildupSummer2010&diff=7249 2010-07-27T12:07:50Z

<p>KingOfDos: /* Zaterdag 7 augustus */</p> <hr /> <div>We beginnen met opbouwen op zaterdag 7 augustus 2010. Je kan aanwezig zijn vanaf 9 uur. In de 3 dagen die daarop volgen hopen we alles ruim op tijd te hebben draaien; dat betekent dat er behoorlijk wat moet gebeuren. Daarna volgen 4 dagen event! Eindelijk!<br /> <br /> Tijdens de opbouw kunnen 20 man aanwezig zijn. Mocht je verder geen crew-taken hebben en wel willen helpen, ben je meer dan welkom vanaf maandagochtend.<br /> <br /> __TOC__<br /> <br /> == Buildup==<br /> === Friday 6 augustus ===<br /> # [[User:zarya|Zarya]]<br /> <br /> <br /> === Zaterdag 7 augustus ===<br /> Overnachting van Zaterdag op Zondag zal niet op het evenemententerrein zijn. Details volgen.<br /> <br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Mishmash|MishMash]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # Syb<br /> # Jacko<br /> # [[User:Fugu|Fugu]] ergens op de middag<br /> # [[User:FooBar|FooBar]] (alleen in de middag) (en standby voor werk ;( )<br /> # [[User:Aczid|Aczid]]<br /> # [[User:KingOfDos|KingOfDos]]<br /> <br /> === Zondag 8 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]] - arriving by bike, will be tired, but maybe can help with small things<br /> # [[User:FooBar|FooBar]] - (en standby voor werk ;( )<br /> # Syb<br /> # Jacko<br /> # [[User:Aczid|Aczid]]<br /> <br /> === Maandag 9 augustus ===<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # &lt;del&gt;[[User:Stitch|Stitch]]&lt;/del&gt; Moet die dag wss even langs werk. Dus ik ben overdag in Gouda.<br /> # [[User:Mischa|Mischa]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:JeroenDekkers|JeroenDekkers]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> <br /> ==Event==<br /> === Dinsdag 10 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Woensdag 11 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Donderdag 12 augustus ===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> === Vrijdag 13 augustus===<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> <br /> ==Teardown==<br /> === Zaterdag 14 augustus ===<br /> # [[User:Stitch|Stitch]]<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:Mischa|Mischa]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]]<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:loupgaroublond|loup]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko<br /> <br /> === Zondag 15 augustus===<br /> # [[User:Stitch|Stitch]] Tot 4 uur smiddags<br /> # [[User:Failbaitr|Jan]]<br /> # [[User:Elmer|Elmer]]<br /> # [[User:MishMash|MishMash]]<br /> # [[User:zarya|Zarya]]<br /> # [[User:Will-Do|Will-Do]]<br /> # [[User:Aequitas|Aequitas]]<br /> # [[User:Cinder|Cinder]]<br /> # [[User:Thyrif|Thyrif]] tot 5 uur smiddags<br /> # [[User:Vicarious|Vicarious]]<br /> # [[User:Fugu|Fugu]]<br /> # [[User:FooBar|FooBar]]<br /> # Syb<br /> # Jacko</div>

KingOfDos http://wiki.eth0.nl/index.php?title=Eth0:2010_Summer_Packinglist&diff=6946 2010-07-12T09:29:46Z

<p>KingOfDos: /* Power stuff */</p> <hr /> <div>This list features a verbose list of all items you can bring to the [[Eth0:2010 Summer/Camping|campsite]].<br /> Some of these things will be provided centrally by Eth0, so we prefer you do not bring them yourself.<br /> <br /> == Camping-basics ==<br /> * tent(s) (big enough to both sleep and put any hardware in)<br /> ** canvas, pegs, guys/lines<br /> ** groundsheet<br /> ** hammer (for the pegs)<br /> * sleeping-stuff<br /> ** airbed with pump / bedroll / matress<br /> ** sleeping bag / blankets / duvet<br /> ** pillow<br /> * clothes stuff<br /> ** clean clothes for one week (pants / t-shirts / underwear / socks / etc.)<br /> ** sweater(s) (for at night, when the temperature drops)<br /> ** extra pair(s) of shoes<br /> ** swimming gear<br /> ** towels (for swimming, showering, etc.)<br /> * personal healthcare<br /> ** dental hygiene (toothbruch / toothpaste / floss wire / mouthwash / etc )<br /> ** shower stuff (biologically degradable!)<br /> ** deodorants<br /> ** shaving stuff, nail clipper<br /> ** hair styling (comb / gel / etc )<br /> ** contact lenses stuff (storage container / enough fluid / etc )<br /> ** hand mirror (for lenses etc)<br /> ** sunblock stuff / aftersun<br /> ** autan (anti-insect goo)<br /> ** small first-aid kit<br /> ** asperin or paracetamol (pain killers)<br /> ** toilet paper (the toilets have this)<br /> ** medicine (please inform the orga about medicine use, where relevant)<br /> * Maglite (with enough batteries or rechargable Maglite )<br /> * lighting for in the tent (tube or LED lights)<br /> * table(s) + chair(s) (for when you put your hardware inside your tent)<br /> * garbage bags &amp; barfbags (in case you get sick)<br /> * small fridge or cool-box<br /> * sufficient money (also in case of emergencies)<br /> * ID-papers (passport / ID-card / driver's license)<br /> * handy<br /> ** sunglasses<br /> ** umbrella<br /> ** battery charger<br /> ** mobile phone (and charger)<br /> ** sticky tape (duct-tape e.d.)<br /> ** earplugs<br /> ** screwdriver set / pocket knife<br /> ** digital camera<br /> ** video camera<br /> ** (table) fan for cooling<br /> ** electric air bed pump<br /> ** bug killers (electric or other)<br /> ** construction canvas (as groundsheet or in case of leakage)<br /> ** party tent / (large) parasol<br /> <br /> == Computer ==<br /> * Computer(s) / Laptop(s) (or iBook e.d.) / PDA(s)<br /> * essential peripherals<br /> ** keyboard<br /> ** mouse<br /> ** external audio speaker set (no mega-stereo set, and quiet at nighttime)<br /> ** headphones<br /> ** adapters/chargers (for things like laptops, speaker sets, etc)<br /> * optional peripherals<br /> ** webcam<br /> ** UPS<br /> ** steering wheel / joystick / etc<br /> * networking<br /> ** 25 metres (or more) UTP CAT5 (or better) cable for each computer or device you need attached to the network<br /> ** a switch (no hubs!)<br /> ** wireless network adapter (802.11g compatible)<br /> * media<br /> ** blank cd-r(w)'s / dvd+r(w) or dvd-r(w)<br /> ** cd-r marker pen<br /> ** installation cd's/dvd's (Windows,Linux,Mac,etc)<br /> ** cd's/dvd's with apps/games/etc<br /> ** drivers<br /> ** boot floppy/cd<br /> * others / fun / handy<br /> ** set of screwdrivers<br /> ** switch with gigabit uplink / gigabit switch<br /> ** KVM Switch (for server management)<br /> ** &lt;s&gt;Wlan accespoint&lt;/s&gt; (No rogue accesspoints. They disturb the eth-0 wifi)<br /> ** Extra/spare UTP CAT5 (or better) cable(s)<br /> * Waterproof bag - saves your vital electronics when the entire camp ground turns into a swamp<br /> <br /> == Power stuff ==<br /> ''(everything WITH grounding (rim earthing)! to prevent accidents etc)''<br /> * sufficient power cables for your computers etc.<br /> * power extension cable (at least 25 meters suggested)<br /> * sufficient sockets for your equipment<br /> * plastic sheeting to keep the power supply dry (where needed)<br /> <br /> == Food stuff ==<br /> * (plastic) drinking cups<br /> * (plastic) plates<br /> * (camping) cutlery<br /> * cooking stuff<br /> ** &lt;s&gt;frying pan + grease&lt;/s&gt; (uses way to much power)<br /> ** gas canister (with good gas tube) / campinggaz<br /> ** matches / lighter for gas cooker<br /> ** pots / pans<br /> ** barbecue (gas is preferred)<br /> ** cooking spoons (for stirring stuff)<br /> ** strainer<br /> ** kitchen roll<br /> * can and bottle opener<br /> * fridge and/or cool-box (for keeping food stuffs cool)<br /> * coffee machine<br /> * water cooker for tea, soup, etc<br /> * washing bowl for the dishes / brush / liquid / tea cloth and hand towels<br /> * drinks for during the event (there are super markets / stores nearby, and a bar on-site)<br /> ** Red Bull / Golden Power<br /> ** &lt;s&gt;Jolt&lt;/s&gt; (There is Mate, Jolt hasn't been for sale for years)<br /> ** Coca Cola<br /> ** 7-up<br /> ** Orange drink<br /> ** orange juice<br /> ** apple juice<br /> ** milk<br /> ** coffee<br /> ** (ice) tea<br /> ** Beer<br /> ** Smirnoff Ice, Flugel, Feigling, Bacardi, Passoa (Diablo), Vodka, safari, Martini, Apfel Korn, Jaegermeister, Whiskey, Jenever, Controux<br /> * snacks (crisps, nuts, candy(licorice etc), etc )<br /> * bread (breadrolls and buns for barbecued food etc.)<br /> * bread toppings (cheese / meat / sweet stuff)<br /> * cans or packs of (instant) soup<br /> * hot dogs / frankfurters<br /> * butter(cup), salt, pepper, sugar, coffee (+ coffee filters), tea<br /> * sauces<br /> ** mayonnaise<br /> ** ketchup<br /> ** curry sauce<br /> ** garlic sauce (may be regarded offensive :-)<br /> ** sate-sauce (peanut)<br /> ** Barbecue sauce<br /> <br /> &lt;small&gt;''This list is a translation of the [http://wiki.nl-crew.com/index.php/Inpaklijst nl-crew.com packing list]. Use of (parts of) this list is granted under the term that this sub-text is present and that corrections / additions are re-inserted into the original list. This list is distributed under the Creative Commons Attribution-Noncommercial-Share Alike 3.0 NL license. Have fun camping! The [http://www.nl-crew.com nl-crew].''&lt;/small&gt;</div>

KingOfDos